Plumbing Basics: What You Need for Installing a Bathtub
Plumbing Basics: What You Need for Installing a Bathtub
Blog Article
In this article in the next paragraph you might get a lot of helpful information concerning How to Install a Bathtub.
Mounting a tub isn't specifically brain surgery, however it does need solid plumbing, carpentry, and also occasionally, tiling skills. Replacing an old bath tub with a new one is also a reasonably hard project. If the old bathtub is easily accessible, the job can move speedily; if you need to open a wall to get rid of the old tub as well as position the brand-new bathtub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will certainly require an assistant to move out the old bathtub as well as set in the new one. Ensure you have actually certified on your own for the task and also fit trying it. Rather than working with a contractor to take control of a halfway-completed project, it is better to think about utilizing one before you begin. Possibilities are you may need a specialist plumber to make tube connections.
This write-up will aid you set up a brand-new bath tub in your bathroom if you have actually currently bought a brand-new tub and do not need to transform the setup of your previous water supply pipes.
Your devices as well as product checklist should comprise the following:
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water. After doing so, switch on the faucets to drain pipes any kind of water staying in the system. The procedure of getting rid of the existing taps can be fairly bothersome due to the limited access that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a fabric all set for the staying water that will originate from the pipes. As soon as the supply pipes have actually been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from transforming throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will need to be cleaned up of any kind of old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic adapter to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap and the other end gives a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin making sure that the washing machines are in area between the tap as well as the sink. Secure the faucet in position with the supplier supplied backnut. As soon as the faucet is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular tap connectors. The previous kind must be attached to the faucet finishes first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing both wood boards under its feet, put the bath tub in the called for placement. The wooden boards are handy in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto 4 small points.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by examining the spirit level and also changing the feet on the bathtub till the spirit level reviews level.
To mount faucets, fit all-time low of the furthest flexible faucet port to the proper supply pipe by making a compression sign up with; then do the very same for the various other faucet.
Turn on the water system as well as check all joints as well as brand-new pipework for leaks and tighten them if needed. Fill the bathtub and additionally inspect the overflow electrical outlet and the normal outlet for leaks.
Finally, repair the bathroom paneling as explained in the maker's user's manual. Tiling as well as securing around the bathtub needs to wait up until the bath tub has actually been used a minimum of once as this will settle it right into its last position.
Planning for the Setup
To start with, the supporting frame provided with the bath needs to be fitted (if required) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to see to it that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets system to stop strain on the bath tub.
Fit the adaptable tap ports to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you use all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its final position.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to split a rigid seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, resulting in difficulties with dampness and feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components and installations. They are marketed in tubes and also cartridges, as well as are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to always fill the tub with water before sealing, to permit the activity experienced when the tub remains in usage. The sealant can split fairly very early if you do not take into consideration this activity before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise quickly readily available on the market. It is recommended to fit the tiles making use of waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a devoted reader on Tools You Need to Install a New Bathtub , I figured sharing that piece of content was really helpful. For those who liked our post if you please remember to pass it around. I cherish reading our article about How to Install a Bathtub.
Best decision? Contact. Report this page